DIY CNC Mill Kit 5 Axis 62oz-in Nema14 Motor EMA2-040D22 Digital Stepper Driver. 5 Axis Kit for CNC DIY. The upgraded 5 axis breakout board is specially designed for the CNC single axis 2-phase stepper driver controller.
The breakout board using high-performance three-state bus driver 74HC244 and Schmitt inverter 74HC14. The input signal is amplified, rectified, filtered to make the drive capability of the output signal more stable and stronger.With this 5 axis breakout board, any 1-5 Microstepper driver controllers can be directly controlled by the PC via the MACH3, KCAM4, etc. Please note: This board uses parallel port to communicate with computer, the USB is used for providing power for the board. The stepper driver board controller in kit is a high performance microstepping driver adopting of 32-bit DSP, pure sine wave subdivision technology.
With this technology and the self-adjustment technology (self-adjust current control parameters) for different motors, the drive motors can run with less noise, lower heating, smoother movement and have better performances at higher speed than most of the drivers in the market. In short, you will get more benefits from the Kit on CNC work, especially extra-low motor noise offers excellent quietness. We have been fulfilling CNC Motion Control needs for over 10 years to support any project you may have. Stepper motors and drivers from ENGMATE. Are with high quality for stable and durable usage.
5-axis stepper motor driver controllers. USB power supply and peripherals powered phase are separated to protect computer security. All the signals are opto-isolated. Which can protect your computer security.
To define the Limit, Emergence-Stop, Cutter alignment etc. Wide input voltage range: 12-24V, and with anti-reverse function. One relay output control interface. Accessed by the spindle motor or the air pump, water pump, etc. Microstep drivers in the market.
For inverter to control the spindle speed. Shape Pulse and direction signals.Data transfer speeds of up to 10MBit/S. Amplification, filtering, enhancement processing drivers enable signal. Extra-low motor noise offers excellent quietness. With 7 stalls output current setting.
Adoption of 32-bit DSP, pure sine wave subdivision technology. Low-vibration and low temperature rising. With 3 stalls microstep subdivision setting. Automatic half-current reduction as long as switching off SW4 when motors stop. Internal optical isolation, pulse input frequency up to.
Short-voltage, over-voltage, over-current and short-circuit protection, protect the motors, driver from being damaged. Suitable for 2-phase and 4-phase Hybrid stepper motors. High torque, more smooth movement. High efficiency, energy-saving, low noise and low vibration. High start torque, low start current and reliable performance.
Simple 4 wires ensure easier wiring, installation and maintenance. High efficiency, high reliability, low cost. PWM control and regulation, insure the steady and precise output voltage. Over-temperature protection: built-in a powerful fan for cooling.
100% full load burn-in test. Over current, over voltage, short circuit. Low output ripple and yawp. Suitable for a variety of small sized automation equipment and instruments.
For any small-and-medium automatic equipment with CNC controller, such as engraving machine, plasma cutting machine, milling machine, foam cutting machine, lathes, laser cutting machine etc.. For other industrial application, such as 3D printer, medical instruments, stage light equipment, robot, music fountain etc.. Electrical Properties of 5Axis Breakout Board(ambient temperature Tj = 25°C).
Get power from PC via USB port and 12-24V power supply for limit/Estop switch. Pulse and Direction Signal Control(EMA2-040D15/EMA2-040D22).Natural Cooling or Fan Forced cooling. Avoid dust, oil fog, corrosive gas. Nema 8, Nema 11, Nema 14, Nema 16, Nema 17. 360W 24V 15A Switching Power Supply 110/220V Switchable Temperature Control.
110VAC/ 220VAC±20% (selected by switch). Australia, New Zealand, South Asia, East Asia.South America, Other Countries/ Regions. Usually, we dispatch your order within. However, 95%+ parcels are delivered within the reference time. Please do contact and confirm with us BEFORE placing order. If you receive a not-as-described e. We will arrange a replacement as soon as the case is confirmed. All qualified return/replacement must be guided by us.
We may not accept your return without communication in advance. By placing an order, you acknowledge that you have accepted the terms and conditions of sale. The item "DIY CNC Mill Kit 5 Axis 62oz-in Nema14 Motor EMA2-040D22 Digital Stepper Driver" is in sale since Tuesday, November 30, 2021.This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "easysupply" and is located in HK. This item can be shipped worldwide.