CNC Set 4 Axis Breakout Board & Nema17 Stepper Motor For DIY Mill/Plasma/Router. High torque, More smooth movement. High efficiency, energy-saving, low noise, low vibration, high start torque, low start current and reliable performance. 4 pcs Nema 17 stepper motor with. Cm, 4 leads, 1.7A.
4 pcs Stepper motor driver DM. 1 pc Power supply 200W-24V. 1 pc breakout board & 1 pc parallal cable. Step Angle: 1.8 degree.Rated Voltage: 2.55 V. Holding torque: 48 oz-in 0.40N. Detent torque: 2.2 N. Number of wire leads: 4 (Black A+ , Green A- , Red B+ , Blue B-).
The diameter for motor shaft is. The diameter of axle is 5mm and the length of the shaft is 24mm. Stepper motor driver DM432, peak 3.5A, 32 micstep. L High performance, low price.L Average current control, 2-phase. L Overvoltage, under voltage, overcorrect, phase short circuit protection. Channels subdivision and automatic idle-current reduction. L 8 channels output phase current setting. L Offline command input terminal. L Motor torque is related with speed, but not related with step/revolution. L High hording torque under high speed. Not condensation, no water droplets.
Prohibition of combustible gases and conductive dust. Pulse signal, PUL+ is the positive end of pulses input pin.
PUL- is the negative end of pulse input pin. DIR signal: DIR+ is the positive end of direction input pin. DIR- is the negative end of direction input pin. EN+ is the positive end of.
EN- is the negative end of. (Using DIP pins to achieve this function). Dip switches 1, 2, and 3 correspond to S1, S2, and S3, respectively.
Motor doesn't run, without holding torque. Wrong connection of stepper motor.RESET signal is effective when offline. Motor doesn't run, butmaintains holding torque. Adjust PMW & signal level. Change connection for any of 2 wires. Motor's holding torque is too small.
Too small relative to current setting. Driver does not match with the motor. Built in DB25 male connector. DB25 Output Pin:P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. DB25 Input Pin: P10, P11, P12, P13, P15.P2 P3 is set to X-axis for the X-axis pulse. P4 P5 is set to Y-axis, Y axis pulse. P6 P7 is set to Z-axis Z-axis pulse. The other can be set to A B C axis.
A-axis pulse P8 P9 is set as the A axis. P14 is set to B-axis B-axis pulse P1.
P16 P17 is set to C-axis, C axis pulse. Can also be set to the spindle control signal \ electrical permit. Input interface for the P10 P11 P12 P13 P15.
Application:Our Stepper Motors are used on small to mid-sized CNC mills or milling machines, CNC lathes, Pick-n-place machines, Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters. Carver machine , Dispenser, Automazation, 3D Printer, Stage lighting, instrument, laser equipment, scanner and so on.
These motors have been used in precision telescope positioning systems and robots. Feedback is very important to us.It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday. The item "CNC Set 4 Axis Breakout Board & Nema17 Stepper Motor For DIY Mill/Plasma/Router" is in sale since Saturday, August 14, 2021. This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "autowelcomehere" and is located in Chino, California. This item can be shipped to United States.