Axis Diy Cnc

Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board

Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board
Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board
Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board
Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board
Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board
Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board
Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board

Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board    Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board

Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board. 3 x stepper motor drivers 2M542. 1 x CNC 5 axis interface board.

Part 1: CNC Stepper Motor Drive 2M542. 20 to 50VDC Supply Voltage. H-Bridge, 2 Phase Bi-polar Micro-stepping Drive. Suitable for 2-phase, 4, 6 and 8 leads step motors, with Nema size 16 to 34.

Output current selectable from 1.0 4.2A peak. Current reduction by 50% automatically, when motor standstill mode is enabled. Pulse Input frequency up to 200 kHz. Optically isolated differential TTL inputs for Pulse, Direction and Enable signal inputs. Selectable resolutions up to 25000 steps.

Over Voltage, Coil to Coil and Coil to Ground short circuit protection. 2M542 is a cost effective, high performance bi-polar two phase micro-stepping drive applying pure-sinusoidal current control technique. It is best suited for the applications that desired extreme low noise and heat. It operates well in an environment, where electricity supply experience instability and fluctuation. The general pseudo-sinusoidal current control technology adopted by majority of the drive produced distorted sine wave, and current ripple, resulting in vibration, noise and motor heating.

This results in motor degrading over time, reducing in motor performance and shortens the usage life. With an automatic optimization speed control technique, the PowerStep series drive output is very stable, with almost zero vibration and noise, performing close to a servo system, allowing the motor to operate smoothly. That helps to fulfill a design requirement of low noise, low heat and high performance. Natural Cooling or Forced Convection. Avoid dust, oil frost and.

Part 2: CNC 5 Axis Interface Board. 1: The maximum matching 5-axis stepper motor driver. 2: The two-stage signal processing, signal transmission smooth, powerful anti-jamming. 3:5 input interface to define the emergency stop, limit, points in the knife, etc. 4: relay output control interface, can be accessed by the spindle motor or the air pump, water pump, etc.

5: five-axis job LED display, visual display products, working condition. Electrical performance (Tj = 25? 5V DC power supply or computer USB to take power.

Received the highest 5-axis independent driving. Pulse + direction + enable signal. In the test machine, note the following before. 1, note that using the 5V power supply. 2, determine the stepper driver works (Model0).

3, to determine the drive wiring step. USA, Australia, United Kingtom, Russia and Ukraine. We do not responsible for any lost because of incorrect address provided.

It usually take 2-3 weeks (USA, CA, AU, UK). Other country 2-4 weeks for you to get it. Later than 7 days the item cannot be accepted for returning. If the order is defective, we will send replacement parts to you after receiving the proof of the defective photos of the items that you received, and no additional charge. We are an export trading online company, glad to serve for you.

24 Hours a Day, 7 Days a Week. We will reply you ASAP. Our aim is to provide Top Level Customer Service , normally so we will try our best to solve any problem. Package included: 3 x stepper motor drivers 2M542 1 x CNC 5 axis interface board 1 x DB25 Cable. The item "Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board" is in sale since Thursday, June 16, 2016.

This item is in the category "Business & Industrial\Automation, Motors & Drives\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "cnctechzone" and is located in Guangzhou. This item can be shipped worldwide.
  • Brand: LEADSHINE
  • MPN: Does Not Apply

Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board    Diy CNC Kit 3 Axis Stepper Motor Driver 2M542 4.2A & Breakout Interface Board